HomeNewsUse Ultrafine Grinding Mill to Get High Quality Powder


Use Ultrafine Grinding Mill to Get High Quality PowderPosted: 2019-05-14

  • Clirik ultrafine grinding mill according to the principle of material layer grinding, the material stays in the mill for a short time, reducing the repeated grinding, so the product contains very little iron, the product whiteness and purity is high, the finished product size is less than 2μm and the powder content can reach 70%, achieving a low residue of 325 mesh, and the primary air selection meets the fineness and quality requirements. The super-fine grinding machine adopts frequency conversion speed regulation, specially designed roller sleeve and liner grinding curve, and adopts mechanical and electronic double limit protection device, which effectively prevents direct contact between the roller sleeve and the disc liner, and effectively improves the grinding efficiency.

    Ultrafine grinding mill

    The ultrafine grinding equipment is equipped with an automatic control system, which can realize remote control and easy operation. It adopts the automatic control of the grinding roller pressure control mode, and the grinding pressure is precisely controlled without manual operation. The grinding roller in operation is not in contact with the grinding disc, and the grinding roller and the lining plate are made of high-quality materials, with less wear and long service life. The main force of the ultra-fine grinding powder process is the motor. The main motor drives the grinding disc to rotate through the reducer. At the same time, the wind enters the CLUM ultra-fine vertical mill from the air inlet. The material falls under the centrifugal force and falls on the grinding disc through the screw feeder. The center moves evenly to the edge. When passing through the grinding roller area on the grinding disc, it is crushed by the grinding roller, and the bulk material is directly crushed. The fine material is squeezed to form a material bed for intergranular pulverization. The pulverized material continues to move toward the edge of the disc until it is carried away by the strong airflow at the wind ring, and the larger particulate material is again dropped onto the grinding disc to continue pulverization. When the material in the airflow passes through the upper separator, the rotor Under the action of the blade, the coarse particles are returned to the grinding disc for grinding. The qualified fine powder is ground together with the airflow and collected by the system's dust collector. The collected powder is the CLUM series vertical superfine grinding. The product.

    Ultrafine grinding equipment

    Ultra fine grinding is a multi-rotor classifier that introduces advanced German technology to achieve ultra-fine powder without pressure. In all industrial milling equipment, the bearing is the key to fixing and reducing the coefficient of load friction in the machine during ultra-fine grinding. Rusting of bearings is an inevitable problem in our use. Generally, the mill equipment is made of steel. In the process of use, the material contains moisture, and there is moisture in the air, which will cause the bearing parts of the pulverizer to rust. The new bearing is a super-fine grinding bearing divided into main bearing and auxiliary bearing. If the main bearing is rusty, you can apply a layer of lubricant on the bearing surface or sand with a fine sandpaper. If the auxiliary bearing is rusty, you can directly change it. Auxiliary bearings, there is a simple method is to put the bearing in the diesel oil slightly inflated when the bearing is rusting, and then sand it with fine sandpaper. This kind of treatment is basically no additional cost, and can guarantee that your production line will not be interrupted. Superfine grinding will become your intimate machine housekeeper. Then the specific parameters and equipment prices, please call +8613512155195 for further details.

    Clirik ultrafine grinding millwww.grindingmill.in/products/1.html

     

     

Previous:Clirik and Mining Word Russia 2019
Next:How to choose the ring material of the grinding mill?

Feedback

Recommend

Ultrafine Grinding Mill

Capacity:0.5-30 t/h
Feeding size:≤20mm
Output Size:5-74um/mesh
Info:HGM Series ultrafine grinding mill is the equipment specializing in producing fine and superfine powder of non-inflammable...

    Contact us

  • Office Address: No.19Fuqing Rd,Shanghai
  • E-mail: Sales@clirik.com
  • Sales Department Tel 0086-21-20236178

Copyright 2014 by Shanghai Clirik Machinery Co. LTD All rights reservedE-mail:sales@clirik.com